Sti 6200WIR8 User Manual download pdf (Page 6)

— 6 —

Mirrored Receiver Operation

The LEDs, the sounder, the siren time and the 12VDC output activation will duplicate the sensor settings enrolled on the master

RECEIVER. If a sensor is enrolled to a mirrored RECEIVER instead of the master, a transmission from the master RECEIVER will

override the mirrored RECEIVER’S LED status. To use any STI keyfob with a master + mirror RECEIVER system, enroll keyfob to

mirrored RECEIVER before adding the mirrored RECEIVER to a system.

Enrolling Mirrored (multiple) Receivers

The LEDs, the sounder, the siren time and the 12VDC output activation will duplicate the sensor settings enrolled on the master

RECEIVER. If LED “latching” is desired on the mirrored RECEIVER, this must be selected at the time of the mirrored RECEIVER’S

enrollment.

NOTE: If a SENSOR is enrolled to a mirrored RECEIVER in error (instead of the master), a transmission from the master RECEIVER

will override the mirrored RECEIVER’S LED status.

1. Check that the module is not in DELETE mode (SW7 OFF).

2. Use SW4 and SW5 to select the mirror number 1-4 if not the master (see Component Descriptions).

3. Enrolling mirrored RECEIVERS is performed in sequential pairs:

Pair Column A Column B

1Master=>Receiver1

2Receiver1=>Receiver2

3Receiver2=>Receiver3

4Receiver3=>Receiver4

NOTE: All SENSORS are enrolled only to the master RECEIVER. The mirrored RECEIVERS copy the master RECEIVER’S output

(except latch settings) sequentially thru RECEIVERS 1 - 4.

4. Set SW1 and SW8 (ON) on the master RECEIVER.

5. Set SW8 (ON) on each mirrored RECEIVER.

6. Enable ENROLL mode, SW2 (ON), on the two RECEIVERS being paired together.

7. Press and release the Push Button on the Column A RECEIVER (above). The Column B receiver will give a double beep.

8. Press and release the Push Button on the Column B RECEIVER (above). The Column A RECEIVER will give a double beep.

NOTE: If Column B RECEIVER was previously enrolled to Column A RECEIVER and was not deleted, the Column A RECEIVER will

not double beep, but will work properly.

9. Disable ENROLL mode, SW2 (OFF), on both RECEIVERS.

10. Press and release the Push Button of the Column A RECEIVER (above). The LED’s of the Column B RECEIVER will light in

the same conﬁguration.

NOTE: Keyfobs must be enrolled into each master or mirror RECEIVER where it will be used.

Keyfob Operation

An STI Keyfob can be used to remotely turn off and on the LEDs, sounder, and outputs on the STI

8-Channel Receiver and also act as a CALL or MANUAL ALERT button. While the STI 8-Channel

Receiver is turned off, it will continue to monitor the sensor signals.

To use an STI keyfob, you can separately enroll the Left/Right buttons and ON/OFF buttons to the

receiver. To use a single STI keyfob with a Master + Mirror Receiver System, enroll the keyfob to

each receiver to be used in the system before adding the Mirrored receivers to the system. To use

multiple keyfobs to independently control each receiver, enroll each keyfob to its respective receiver

before adding the Mirrored receivers to the system.

Enrolling Keyfob On/O Buttons

Keyfob ON/OFF buttons do not enroll into zones. The keyfob ON/OFF buttons will turn on and off all 8-Channel receiver out-

puts. Cycling these buttons remotely activates the push button.

1. Check that the module is not in DELETE mode (SW7 OFF).

2. Enable ENROLL mode set (SW2 ON).

3. Press either the ON or OFF button on the keyfob.

4. The RECEIVER will give a double beep. ON/OFF keyfob buttons will not be assigned to a zone LED.

5. Repeat steps 2-4 to enroll another keyfob.

6. To exit ENROLL mode set (SW2 OFF).

NOTE: The RECEIVER will only operate with 8 keyfob Left/Right buttons enrolled into zones and 8 keyfob ON/OFF buttons

enrolled into memory. If a ninth keyfob’s ON/OFF button is enrolled, the keyfob’s ON/OFF buttons enrolled ﬁrst will be deleted.

Enrolling Keyfob LEFT/RIGHT Buttons

Keyfob LEFT/RIGHT buttons enroll into a zone. The keyfob LEFT button is a CALL or MANUAL ALERT button and the RIGHT

button is a RESTORE. Follow the same steps for Enrolling Sensors into Zones and Deleting Single Zones for the Keyfob LEFT/

RIGHT buttons.

19018 ANCHOR

(4) PROVIDED

MARK AND DRILL

3/16 DIAMETER HOLES

(4) PLACES

19108 NYLON WASHER

(4) PROVIDED

19039 SCREW

(4) PROVIDED

PUSH BUTTON

19081 FRONT COVER SCREW

PUSH BUTTON SWITCH

Represents any STI 433 MHz sensor transmitting ONLY to a Master Receiver

SYSTEM 1

SYSTEM 2

MULTLIPLE SYSTEMS

Master

Receiver

Mirror #1

Receiver

Mirror #2

Receiver

Up to

1000 ft

Up to

1000 ft

Up to

1000 ft

Up to

1000 ft

Up to

1000 ft

Up to

1000 ft

Master

Receiver

Mirror #1

Receiver

Master

Receiver

Mirror #1

Receiver

Mirror #2

Receiver

- Last

Mirror #2

Receiver

- Last

Monitors Housed in a

Central Office or Location

SINGLE SYSTEM

Mirror #3

Receiver

Up to

1000 ft

Mirror #4

Receiver

- Last

Up to

1000 ft

Switches (1-8) - For reference, information is also written on the

receiver case (located under Zone ID list).

1 - MIRROR MASTER OFF/ON

2 - NORMAL/ENROLL

3 - AUTO RESTORE/LATCH

4 - SIREN TIME/MIRROR#

5 - SIREN TIME/MIRROR#

6 - CHIME OFF/ON

7 - NORMAL/DELETE

8 - MIRROR SLAVE OFF/ON

SIREN

SW4 SW5 TIME MIRROR #

OFF OFF DISABLED 1

ON OFF 30 SEC 2

OFF ON 180 SEC 3

ON ON ON CONT 4

Embossed Programming Instructions:

ZONES:

LEFT BUTTON

“CALL”

RIGHT BUTTON

“RESTORE”

NO ZONE:

ON and OFF

BUTTONS

1 - MIRROR MASTER OFF/ON

2 - NORMAL/ENROLL

3 - AUTO RESTORE/LATCH

4 - SIREN TIME/MIRROR#

5 - SIREN TIME/MIRROR#

6 - CHIME OFF/ON

7 - NORMAL/DELETE

8 - MIRROR SLAVE OFF/ON

SIREN

SW4 SW5 TIME MIRROR #

OFF OFF DISABLED 1

ON OFF 30 SEC 2

OFF ON 180 SEC 3

ON ON ON CONT 4

ANTENNAS

SWITCHES 1-8

ZONE LEDs

PUSH BUTTON

PIEZO

COVER

SCREW

DIPSWITCH

FUNCTIONS

WIRE ROUTE

OPTION 1

FORM C

SWITCH OUTPUTS

12V INPUTS

TERMINALS 500mA

12V OUTPUTS

TERMINALS 300mA

WIRE ROUTE

OPTION 2

TRIGGERED OUTPUT PLUG

12V , 75mA

PLUG IN ADAPTER

12V , 500mA

SURFACE FEET (x4)

(WALL MOUNTING HOLES)

EMBOSSED

INPUT AND

OUTPUTS

FCC ID: TXL34108

MODEL #34108

IC: 6335A-34108

SAFETY TECHNOLOGY INTERNATIONAL

WATERFORD, MI U.S.A.

REDDITCH, WORCESTERSHIRE UK

Trigger

Output

12 V

75mA

N.O.

COM

N.C.

+ 12 V

- IN

500 mA

300 mA

PLUG IN ADAPTER

12 V 500mA

ANTENNAS

SWITCHES 1-8

ZONE LEDs

PUSH BUTTON

PIEZO

COVER

SCREW

DIPSWITCH

FUNCTIONS

+ 12 V

- OUT

WIRE ROUTE

OPTION 1

FORM C

SWITCH OUTPUTS

12V INPUTS

TERMINALS 500mA

12V OUTPUTS

TERMINALS 300mA

WIRE ROUTE

OPTION 2

TRIGGERED OUTPUT PLUG

12V , 75mA

PLUG IN ADAPTER

12V , 500mA

EMBOSSED

INPUT AND

OUTPUTS

FCC ID: TXL34108

MODEL #34108

IC: 6335A-34108

SAFETY TECHNOLOGY INTERNATIONAL

WATERFORD, MI U.S.A.

REDDITCH, WORCESTERSHIRE UK

Trigger

Output

12 V

75mA

N.O.

COM

N.C.

+ 12 V

- IN

500 mA

300 mA

PLUG IN ADAPTER

12 V 500mA

+ 12 V

- OUT

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Sti 6200WIR8 User Manual Page 6

Comments to this Manuals

Related products and manuals for Safety Sti 6200WIR8