Sti 6200WIR8 User Manual download pdf (Page 5)

— 5 —

Enrolling Sensors into Zones

1. Check that the module is not in DELETE mode (SW7 OFF).

2. If the zone should have “latching” set (SW3 ON).

3. Enable ENROLL mode set (SW2 ON).

4. CheckthatthezoneashingGREENiscorrect,andnotethezone(s)withREDLEDs.

5. Change the status of the SENSOR to be enrolled by triggering an alert on the SENSOR and return it to the non-triggered

state (if done manually).

6. The RECEIVER will give a double beep and the zone LED will change to continuous RED.

7. Repeat steps 2-6 to enroll another SENSOR.

8. To exit ENROLL mode set (SW2 OFF).

ZONE ENROLLING AND DELETING PROCEDURES

The STI 8-Channel Receiver is designed to receive ONLY wireless signals from products in the STI Alert Series (see back of

the installation instructions). The RECEIVER allows you to enroll up to 8 devices into zones 1 thru 8. The RECEIVER will enroll

from different SENSORS directly or by enrolling other mirrored RECEIVERS. The RECEIVER also enrolls up to eight keyfobs.

When ENROLL mode is enabled (SW2 ON), the LEDs for any currently enrolled zones will turn RED to indicate these zones

arenotavailable.TheLEDwillashGREENtoindicatetheavailablezonetobeenrolled.Pressthepushbuttontochange

toadifferentzonetobeenrolled.ThenextavailablezonewillhavetheashingGREENLED.TheRECEIVERwillnotallow

enrollment into an occupied zone. The RECEIVER will not allow the same device to be enrolled into more than one zone.

The RECEIVER will not enter ENROLL mode while it is in DELETE mode (i.e. DIP SW7 ON).

Zone Latching

“Latching” lets you know a zone alert was previously triggered but the alert has also been cleared. When a zone is in the

“latched”status,thezoneLEDwillashRED.Forexample,whenadoorSENSORhasbeenopenedandclosed,thezoneLED

willashREDtoindicatethedoorwasopenedpreviously,butisnolongeropened.

The latching is released when the user presses the push button to indicate acknowledgement of the alert. When the “latched”

status is released, the zone LED will change back to continuous GREEN. If the zone has another alert before the “latched”

statusisreleased,theLEDwillchangetocontinuousREDinthealertstate,andthenbacktoashingwhenthealertiscleared.

A zone will have “latching” when SW3 is (ON) at the time of enrollment. If zone latching is not selected at the time of enrollment

(SW3 OFF), the zone LED will change from continuous RED back to continuous GREEN when the alert has been cleared.

Low Battery / Tamper Detection / Out of Range SENSOR Alerts

If the battery is too weak, something has triggered a tamper alert signal from the SENSOR, or the SENSOR has been out of range

between 12 - 24 hours, the zone LED will light AMBER to alert a need for attention to that device.

Sensor Installation Tip

When ﬁrst enrolling a SENSOR, set the “latching” on (SW3 ON), and bring the SENSOR to the RECEIVER location to enroll it

before mounting the SENSOR. Then, mount the SENSOR at its intended location and trigger an alert on the SENSOR. Check

thezoneontheRECEIVERtoseeifitiscontinuousREDorashingRED,whichmeansitreceivedtheSENSOR’Ssignal.Then,

if latching is not desired, delete that zone (see Deleting Single Zones) and enroll the SENSOR again without latching (SW3

OFF), from the mounted location.

See Enrolling Mirrored (multiple) Receivers

1 2 3 4 5 6 7 8

No comments

Sti 6200WIR8 User Manual Page 5