Sti 1221D User Manual download pdf (Page 1)

Safety Technology International, Inc.

2306 Airport Road • Waterford, Michigan 48327-1209

Phone: 248-673-9898 • Fax: 248-673-1246

Toll Free: 800-888-4784 • E-mail: [email protected]

Web: www.sti-usa.com

Safety Technology International (Europe) Ltd.

Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch

Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999

Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)

E-mail: [email protected]om • Web: www.sti-europe.com

INSTALLATION OF STI-1221D STROBE DAMAGE STOPPER

All speciﬁcations and information shown were current as of publication and are subject to change without notice.

INSTALLATION NOTES

1. To minimize strobe light loss, regardless of the type of strobe appliance used, center cover over the

strobe light lens. Failure to follow these instructions may lead to light loss transmission.

2. Damage Stopper must be installed to comply with applicable NEC, NFPA and local codes.

3. In applications where wash downs, rainfall or condensation occur, it is recommended that a drain or

weep hole be provided. Refer to weep hole installation diagram.

4. Damage Stopper may be installed outdoors when appliance carries an outdoor rating.

Electronic warranty form at www.sti-usa.com/wc14

1221DIS APRIL2006

CLEANING INSTRUCTIONS

Rinse with water to remove abrasive

dust and dirt. Wash with soap or

mild detergent, using a soft cloth

(do not scrub). Rinse once more then

dry with a soft cloth or chamois. To

remove grease or wet paint, rub

gently with a cloth wetted with

naphtha. Then wash and rinse. DO

NOT USE RAZOR BLADES.

INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW

1. Using back box assembly as a template, place against mounting

surface at proper location according to NFPA 72.

2. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 in. (25mm) deep.

3. If conduit is present, select the proper inserts and slide them into the

back box notch.

4. Insert the (4) anchors into the wall.

5. Mount back box to wall with screws.

6. Install electrical ﬁttings as needed.

7. Install strobe appliance.

8. Install cover with clips and screws.

9. Test appliance according to appliance manufacturer’s instructions.

INTERNAL DIMENSIONS

WEEP HOLE INSTALLATION

LOCATED IN THIS AREA

DRILL A .25 in.(6.3mm) DIA

. HOLE

APPROX

CENTER LINE

OF UNDERSIDE OF

COVER

1 in.(25mm)

19033 ANCHOR

(4) PROVIDED

EXISTING

FLUSH MOUNT

HORN/STROBE

APPLIANCE

629764 CLAMP

(4) PROVIDED

19013 SCREW

#10 x 1 1/2 in.

(4) PROVIDED

SURFACE MOUNTED

CONDUIT INSERTS

(USE WHERE NEEDED)

ONE OF EACH PROVIDED

IF ADDED PROTECTION IS

NEEDED DUE TO ENVIROMENTAL

CONDITIONS ORDER SUB-121

ENVIRO KIT

19047 #8-32 x 3/8 in.

SOCKET HEAD CAP SCREW

(4) PROVIDED

06297D BACKBOX

HEIGHT

8.5 in.(216mm)

DEPTH

5.75 in.(146mm)

WIDTH

6.5 in.(165mm)

01221 COVER ONLY

01221 COUVERCLE SEULEMENT

LOCATED IN THIS AREA

DRILL A .25 in.(6.3mm) DIA. HOLE

APPROX

CENTER LINE

OF UNDERSIDE OF

COVER

1 in.(25mm)

19033 ANCHOR

(4) PROVIDED

EXISTING

FLUSH MOUNT

HORN/STROBE

APPLIANCE

629764 CLAMP

(4) PROVIDED

19013 SCREW

#10 x 1 1/2 in.

(4) PROVIDED

SURFACE MOUNTED

CONDUIT INSERTS

(USE WHERE NEEDED)

ONE OF EACH PROVIDED

IF ADDED PROTECTION IS

NEEDED DUE TO ENVIROMENTAL

CONDITIONS ORDER SUB-121

ENVIRO KIT

19047 #8-32 x 3/8 in.

SOCKET HEAD CAP SCREW

(4) PROVIDED

06297D BACKBOX

HEIGHT

8.5 in.(216mm)

DEPTH

5.75 in.(146mm)

WIDTH

6.5 in.(165mm)

01221 COVER ONLY

01221 COUVERCLE SEULEMENT

INSTALL CLAMP IN NOTCH 2 AS SHOWN

REMARQUES SUR L’INSTALLATION

1. Aﬁn de minimiser la perte de lumière stroboscopique, quel que soit le type de stroboscope utilisé,

le couvercle doit être centré sur l’objectif stroboscopique. Le fait d’omettre ces instructions risque

d’entraîner la perte de diffusion de la lumière.

2. Le Stopper de dégâts doit être installé de sorte à être conforme avec les normes NEC, NFPA

applicables et les codes locaux.

3. Dans les applications où des jets d’eau, des précipitations ou de la condensation se produisent,

il est recommandé de prévoir un trou de vidange ou une barbacane. Reportez-vous à schéma

d’installation d’une barbacane.

4. Il est possible d’installer un Stopper de dégâts à l’extérieur lorsque l’appareil est homologué pour

utilisation à l’extérieur.

1 2

Summary of Contents

Page 1 - REMARQUES SUR L’INSTALLATION

Safety Technology International, Inc.2306 Airport Road • Waterford, Michigan 48327-1209Phone: 248-673-9898 • Fax: 248-673-1246Toll Free: 800-888-4784

Page 2 - STI-1210 / STI-1221 SERIES

• This enclosure is rated to protect signaling appliances indoors and in areas of indirect weather exposure.The cover may be used outdoors only with d

Comments to this Manuals

No comments

Sti 1221D User Manual Page 1

Browse online or download User Manual for Safety Sti 1221D. STI 1221D Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Sti 1221D User Manual Page 1

Browse online or download User Manual for Safety Sti 1221D. STI 1221D Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Sti 1221D