Sti 7523 User Manual Page 1

Browse online or download User Manual for Safety Sti 7523. STI 7523 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
MAGNET
6297520 GASKET
(
1) PROVIDED
04874
MOUNTING
PLATE
SCREW #8-32 x 1/2 in.
(4) PROVIDED
AMS-10S MAGNETIC CONTACT
S
WITCH WITH 24 in. WIRE LEADS
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
06298 MOUNTING TABS
(4) PROVIDED
19033 ANCHOR
(
4) PROVIDED
STI-7523 THUMB LOCK
STI-7522 KEY LOCK AVAILABLE
S
T
OP
S
T
O
P
E
M
E
R
G
E
N
C
Y
U
S
E
O
N
L
Y
INSTALLATION OF STI-7522 & STI-7523 PROTECTIVE CABINET
Safety Technology International, Inc. • 2306 Airport Rd. • Waterford, Michigan 48327-1209 • 800-888-4784 • Fax: 248-673-1246 • Web: www.sti-usa.com • Email: [email protected]
ALARM MOUNTING PLATE
CABINET
WIRE ACCESS HOLE
ROUTE THE 2 SWITCH WIRES
THROUGH THE HOLE AS SHOWN
VIEW A
OPTIONAL MOUNTING
HOLES (4)
A
9 VOLT ALKALINE BATTERY
ALARM COVER
19016 TAMPERPROOF TOOL
19032 KEY (2) PROVIDED
19011 SCREW - TAMPERPROOF
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
ALARM MOUNTING PLATE
06202 BACKPLATE
ST
OP
EMER
GENC
Y
US
E
ONL
Y
STOP
19018 ANCHOR (2) PROVIDED
T
INSTALLATION OF STI-7523 ENCLOSURE
1. Insert the (4) mounting tabs fully into backbox mounting tab
slots. Use rubber mallet if necessary.
2. After selecting a suitable location, place enclosure in closed
position, against the wall. Mark and drill (4) 1/4 in. diameter
holes. Insert the (4) 19033 anchors. Close and lock enclosure.
3. Place enclosure in position making sure the (2) switch wires
are not pinched between the wall and enclosure. Drive in the
(4) screws. Enclosure is now secure.
1. Place the alarm mounting plate on the
top center of enclosure. Select at least
two of the four optional mounting
holes. Mark and drill 3/16 in. holes and
install the 19018 anchors.
2. Fish the magnetic switch wires through
the alarm mounting plate and the siren
backplate (View A). Next, drive the two
alarm mounting screws into the
previous installed anchors.
3. Install the two magnetic switch wires
following the terminal switch diagram
(View B).
4. Install the alarm cover using the (2)
tamperproof screws and provided tool.
* 1/4” Diameter
INSTALLATION OF ALARM ASSEMBLY
3.125 in.(79mm)
10.875 in.
(276mm)
8.875 in.(225mm)
STOP
EMERGENCY USE ONLY
P
FRONT VIEW
TOP VIEW
1
6.00 in.
(406mm)
M
*
Page view 0
1 2

Summary of Contents

Page 2 - CIRCUIT BOARD SET-UP

SWITCH SETTINGSVolume - High (105 dB) at 1 ft. ON*Volume - Low (95 dB) at 1 ft. OFFDuration - 30 Second Alarm OFF OFFDuration - 180 Second Alarm O

Related models: 7522

Comments to this Manuals

No comments