Sti 34108 User Manual download pdf

QUICK SETUP GUIDE

STI-34401 Universal Sensor

With 4-Channel Receiver

TO SETUP:

1. Open cover. Remove battery isolator strip.

2. Conﬁgure jumpers - select one of the following: magnetic sensor, tilt sensor, external terminals.

3. Replace cover.

4. Program into receiver.

5. Mount where needed.

CONFIGURE JUMPERS:

PROGRAM 4-CHANNEL RECEIVER WITH SENSOR:

Please read this section completely before proceeding.

1. Plug antenna into the antenna (red) connector on the receiver.

2. Plug adapter into the wall.

3. While holding down the gray button, plug the adapter into the 4-Channel Receiver. A series of beeps/tones will begin playing. Release

button when beeps/tones ﬁnish. The red and green LED’s will ﬂash quickly. The receiver is now in program mode and you have 1 minute to program

all sensors.

4. Activate a sensor to program into 4-Channel (refer to your sensor instructions). A tone or series of beeps will sound representing the channel the

sensor programmed into (i.e.: one beep is zone 1, two beeps is zone 2, etc.).

5. If more sensors are to be programmed, repeat step 4.

6. After programming sensor(s), wait a minimum of 5 seconds, press gray button to exit Program Mode or receiver will exit program mode automatically

within one minute.

CHECK SENSOR:

1. Trigger the sensor. Receiver will emit the alert tone and red light will ﬂash. For multiple sensors, the receiver will beep a number of times (for the

number of the sensor, 1 through 4) and play the alert tone.

2. If red light ﬂashes but there is no tone, the receiver is in silent mode. To exit silent mode press and hold the button until you hear a single beep

then release. Repeat step 6 to hear the receiver alert tone.

CLEAR SENSOR FROM 4-CHANNEL RECEIVER:

1. Disconnect power from receiver and wait approximately 15 seconds.

2. Reconnect power to the receiver, the receiver will make a start-up tone. The green LED will be solid.

3. Within 3 seconds press and hold down the gray button, you will hear a series of beeps/tones. When you hear a continuous tone, let go of the

button; the sensors are cleared.

For additional features and instructions refer to full instruction manual provided with your product.

APPROXIMATE GAP (1 INCH)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

“RESTORE”

CLOSED

“ALERT”

CLOSED

“ALERT”

OPENED

APPROXIMATE GAP (1 INCH)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

REED SWITCH CABLE

(18 INCHES)

APPROXIMATE GAP

(GREATER THAN 1 1/3 INCHES)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

“ALERT”

“RESTORE”

“ALERT”

OPENED

APPROXIMATE GAP

(GREATER THAN 1 1/3 INCHES)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

VINYL ELECTRICAL

TAPE

19039 SCREW

(2) PROVIDED

KNOCK OUT FOR WIRES

OF EXTERNAL SWITCH

“RESTORE”

CLOSED

“ALERT”

OPEN

MAGNETIC SENSOR

“ALERT”

“RESTORE”

TILT SENSOR

EXTERNAL TERMINALS

“RESTORE”

CLOSED

“ALERT”

OPEN

EXTERNAL SWITCH

CONNECTION BLOCK

ONBOARD REED SWITCH

LOCATION FOR

MAGNETIC SENSOR

EXTERNAL SWITCH

CONNECTION BLOCK

TAMPER SWITCH

ONBOARD

REED SWITCH

OPTION 1 MOUNTING

(DOUBLE SIDED FOAM TAPE)

OPTION 2 MOUNTING

VINYL ELECTRICAL

TAPE

19039 SCREW

(2) PROVIDED

KNOCK OUT FOR WIRES

OF EXTERNAL SWITCH

EXTERNAL SWITCH

CONNECTION BLOCK

TAMPER SWITCH

ONBOARD

REED SWITCH

APPROXIMATE GAP (1 INCH)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

“RESTORE”

CLOSED

“ALERT”

CLOSED

“ALERT”

OPENED

APPROXIMATE GAP (1 INCH)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

REED SWITCH CABLE

(18 INCHES)

APPROXIMATE GAP

(GREATER THAN 1 1/3 INCHES)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

“ALERT”

“RESTORE”

“ALERT”

OPENED

APPROXIMATE GAP

(GREATER THAN 1 1/3 INCHES)

GAP MAY BE EFFECTED

IF MOUNTED ON METAL.

VINYL ELECTRICAL

TAPE

19039 SCREW

(2) PROVIDED

KNOCK OUT FOR WIRES

OF EXTERNAL SWITCH

“RESTORE”

CLOSED

“ALERT”

OPEN

MAGNETIC SENSOR

“ALERT”

“RESTORE”

TILT SENSOR

EXTERNAL TERMINALS

“RESTORE”

CLOSED

“ALERT”

OPEN

EXTERNAL SWITCH

CONNECTION BLOCK

ONBOARD REED SWITCH

LOCATION FOR

MAGNETIC SENSOR

EXTERNAL SWITCH

CONNECTION BLOCK

TAMPER SWITCH

ONBOARD

REED SWITCH

OPTION 1 MOUNTING

(DOUBLE SIDED FOAM TAPE)

OPTION 2 MOUNTING

VINYL ELECTRICAL

TAPE

19039 SCREW

(2) PROVIDED

KNOCK OUT FOR WIRES

OF EXTERNAL SWITCH

EXTERNAL SWITCH

CONNECTION BLOCK

TAMPER SWITCH

ONBOARD

REED SWITCH

Magnetic Sensor (supervised)

Tilt Sensor (supervised)

External Terminals (supervised)

Magnetic Sensor (not supervised)

Tilt Sensor (not supervised)

External Terminals (not supervised)

NOTE: To ensure jumpers do not reattach or short to other

components, cut both jumper leads ﬂush to PCB and remove

jumper wire.

Cut jumpers with “X”, do not cut jumpers with “ .“

J1 J2 J3

X X

X X X

Program sensor

before installation

12/12

STI-30104

LAMP CONTROLLER

(OPTIONAL)

AC ADAPTER

GREEN

LED

TRANSISTOR

OUTPUT JACK

RECEIVER ANTENNA

SPEAKER

STI-34104

INDOOR RECEIVER

BUTTON

RED LED

SENSOR TRANSMITTER CAP

SENSOR TRANSMITTER BASE

MOUNTING

TUBE CAP

WALL MOUNT (INCLUDED)

NOT NEEDED FOR POLE

MOUNT INSTALLATION

2 “C” BATTERIES

(NOT INCLUDED)

SENSOR TRANSMITTER

12”MOUNTING TUBE

MOUNTING STAKE

SENSOR TRANSMITTER

BOTTOM

SENSOR TRANSMITTER

MOUNTING

TUBE CAP

MOUNTING STAKE

SENSOR TRANSMITTER BOTTOM

SCREWS

RECHARGEABLE NiMH BATTERIES

SENSITIVITY JUMPERS

(SOLAR TYPE)

SENSITIVITY JUMPERS

(BATTERY TYPE)

FINGER

NOTCHES

REMOVE PLASTIC TAB

FROM BATTERIES

DRIVEWAY

3’OR

LESS

25' OR MORE

PLACE SENSOR

TRANSMITTER 3' OR

LESS FROM EDGE OF

DRIVEWAY AND 25'

OR MORE FROM STREET.

12’

MAX

DRIVEWAY

PLACE SENSOR

TRANSMITTER 3' OR

LESS FROM EDGE OF

DRIVEWAY AND 25+

FEET OR MORE FROM

STREET.

25' OR MORE

3' OR

LESS

12'

MAX

DETAIL B

SCALE 2:1

FINGER NOTCHES

DO NOT

PULL ANTENNA!

WALL MOUNT (INCLUDED)

NOT NEEDED FOR POLE

MOUNT INSTALLATION

SENSITIVITY

ADJUSTMENT

SENSITIVITY

ADJUSTMENT

POWER CONNECTOR ANTENNA CONNECTOR

12”MOUNTING TUBE

GREEN

LED

TRANSISTOR

OUTPUT JACK

RECEIVER ANTENNA

SPEAKER

BUTTON

RED LED

POWER CONNECTOR ANTENNA CONNECTOR

4 CHANNEL RECEIVER

1 2

QUICK SETUP GUIDE 1

Summary of Contents

Page 1 - QUICK SETUP GUIDE

QUICK SETUP GUIDESTI-34401 Universal SensorWith 4-Channel ReceiverTO SETUP:1. Open cover. Remove battery isolator strip.2. Conﬁgure jumpers - select

Page 2

QUICK SETUP GUIDESTI-34401 Universal SensorWith 8-Channel ReceiverTO SETUP:1. Open cover. Remove battery isolator strip.2. Conﬁgure jumpers - select

Comments to this Manuals

No comments

Sti 34108 User Manual

Browse online or download User Manual for Safety Sti 34108. STI 34108 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Sti 34108